Ironwood-electronics Clip Use Instructions Bedienungsanleitung PDF herunterladen

CLEANING THE CLIP

Clean the Clip contacts before each installation. Debris

on the contacts can interfere with its function.

INSTALLING THE CLIP

Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion

between the legs, more force than usual is required during installation. This is due to the fact that there is

excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip

package far less force will be required.

Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.

Electrostatic discharge can damage electronic components.

1. Clean the Clip as described above.

2. Allow the Clip to seek its own alignment by resting it on the chip package.

3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-

rectly positioned between the legs of the chip package.

Installation of the Clip with any improper alignment can result in damage to the chip package legs and the

Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable

are attached to the Clip during installation, the tactile response is diminished and greater care must be

taken with initial positioning.

CAUTION

CLEANING THE CLIP

Clean the Clip contacts before each installation. Debris

on the contacts can interfere with its function.

INSTALLING THE CLIP

Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion

between the legs, more force than usual is required during installation. This is due to the fact that there is

excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip

package far less force will be required.

Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.

Electrostatic discharge can damage electronic components.

1. Clean the Clip as described above.

2. Allow the Clip to seek its own alignment by resting it on the chip package.

3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-

rectly positioned between the legs of the chip package.

Installation of the Clip with any improper alignment can result in damage to the chip package legs and the

Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable

are attached to the Clip during installation, the tactile response is diminished and greater care must be

taken with initial positioning.

CAUTION

CLEANING THE CLIP

Clean the Clip contacts before each installation. Debris

on the contacts can interfere with its function.

INSTALLING THE CLIP

Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion

between the legs, more force than usual is required during installation. This is due to the fact that there is

excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip

package far less force will be required.

Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.

Electrostatic discharge can damage electronic components.

1. Clean the Clip as described above.

2. Allow the Clip to seek its own alignment by resting it on the chip package.

3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-

rectly positioned between the legs of the chip package.

Installation of the Clip with any improper alignment can result in damage to the chip package legs and the

Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable

are attached to the Clip during installation, the tactile response is diminished and greater care must be

taken with initial positioning.

CAUTION

CLEANING THE CLIP

Clean the Clip contacts before each installation. Debris

on the contacts can interfere with its function.

INSTALLING THE CLIP

Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion

between the legs, more force than usual is required during installation. This is due to the fact that there is

excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip

package far less force will be required.

Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.

Electrostatic discharge can damage electronic components.

1. Clean the Clip as described above.

2. Allow the Clip to seek its own alignment by resting it on the chip package.

3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-

rectly positioned between the legs of the chip package.

Installation of the Clip with any improper alignment can result in damage to the chip package legs and the

Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable

are attached to the Clip during installation, the tactile response is diminished and greater care must be

taken with initial positioning.

CAUTION

Position contacts between legs

Gravity only

Slight rotation without pressure

Ironwood Electronics, Inc.

CLIP USE INSTRUCTIONS

1. Use a common toothbrush to remove any dust

between the contacts. The individual contacts are

engineered to be durable; nevertheless take appro-

priate care when brushing them to avoid damage.

2. Use precision dusting cleaner (also known as inert

dusting gas or compressed air in a can) to remove

debris loosened by the brushing.

1 2

CLIP USE INSTRUCTIONS 1

Inhaltsverzeichnis

Seite 1 - CLIP USE INSTRUCTIONS

CLEANING THE CLIPClean the Clip contacts before each installation. Debrison the contacts can interfere with its function.INSTALLING THE CLIPExtra care

Seite 2

INSTALLING THE CLIP (CONT)4. Apply a constant downward force after the contacts are centered between the legs.Proper seating of the contacts is propor

Kommentare zu diesen Handbüchern

Keine Kommentare

Ironwood-electronics Clip Use Instructions Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Ironwood-electronics Clip Use Instructions herunter. Ironwood Electronics Clip Use Instructions User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Ironwood-electronics Clip Use Instructions